ZHCST39A December   2022  – September 2023 AFE11612-SEP

PRODUCTION DATA  

  1.   1
  2. 1 特性
  3. 2 应用
  4. 3 说明
  5. 4 Revision History
  6. 5 Pin Configuration and Functions
  7. 6 Specifications
    1. 6.1  Absolute Maximum Ratings
    2. 6.2  ESD Ratings
    3. 6.3  Recommended Operating Conditions
    4. 6.4  Thermal Information
    5. 6.5  Electrical Characteristics
    6. 6.6  Timing Characteristics
    7. 6.7  Timing Diagrams
    8. 6.8  Typical Characteristics: DAC
    9. 6.9  Typical Characteristics: ADC
    10. 6.10 Typical Characteristics: Internal Reference
    11. 6.11 Typical Characteristics: Temperature Sensor
    12. 6.12 Typical Characteristics: Digital Inputs
  8. 7 Detailed Description
    1. 7.1 Overview
    2. 7.2 Functional Block Diagram
    3. 7.3 Feature Description
      1. 7.3.1 Primary ADC Operation
        1. 7.3.1.1 Analog Inputs
          1. 7.3.1.1.1 Single-Ended Analog Input
          2. 7.3.1.1.2 Fully Differential Input
        2. 7.3.1.2 ADC Trigger Signals (See AFE configuration register 0 )
        3. 7.3.1.3 Double-Buffered ADC Data Registers
          1. 7.3.1.3.1 ADC Data Format
        4. 7.3.1.4 SCLK Clock Noise Reduction
        5. 7.3.1.5 Data Available Pin (DAV)
        6. 7.3.1.6 Convert Pin (CNVT)
        7. 7.3.1.7 Analog Input Out-of-Range Detection (See The Analog Input Out-of-Range Alarm Section)
        8. 7.3.1.8 Full-Scale Range of the Analog Input
      2. 7.3.2 Secondary ADC and Temperature Sensor Operation
        1. 7.3.2.1 Remote Sensing Diode
        2. 7.3.2.2 Ideality Factor
        3. 7.3.2.3 Filtering
        4. 7.3.2.4 Series Resistance Cancellation
        5. 7.3.2.5 Reading Temperature Data
        6. 7.3.2.6 Conversion Time
      3. 7.3.3 Reference Operation
        1. 7.3.3.1 Internal Reference
        2. 7.3.3.2 External Reference
      4. 7.3.4 DAC Operation
        1. 7.3.4.1 Resistor String
        2. 7.3.4.2 DAC Output
          1. 7.3.4.2.1 Full-Scale Output Range
          2. 7.3.4.2.2 DAC Output After Power-On Reset
        3. 7.3.4.3 Double-Buffered DAC Data Registers
        4. 7.3.4.4 Load DAC Latch
        5. 7.3.4.5 Synchronous Output Updating
        6. 7.3.4.6 Clear DACs
        7. 7.3.4.7 DAC Output Thermal Protection
      5. 7.3.5 Alarm Operation
        1. 7.3.5.1 Analog Input Out-of-Range Alarm
        2. 7.3.5.2 ALARM Pin
        3. 7.3.5.3 Hysteresis
        4. 7.3.5.4 False-Alarm Protection
      6. 7.3.6 General-Purpose Input and Output Pins (GPIO-0 To GPIO-7)
      7. 7.3.7 Device Reset Options
        1. 7.3.7.1 Hardware Reset
        2. 7.3.7.2 Software Reset
        3. 7.3.7.3 Power-On Reset (POR)
    4. 7.4 Device Functional Modes
      1. 7.4.1 DAC Output Mode
      2. 7.4.2 ADC Conversion Modes
        1. 7.4.2.1 Programmable Conversion Rate
        2. 7.4.2.2 Handshaking with the Host (See AFE configuration register 0 )
    5. 7.5 Programming
      1. 7.5.1 I2C-Compatible Interface
        1. 7.5.1.1 F/S-Mode Protocol
        2. 7.5.1.2 Hs-Mode Protocol
        3. 7.5.1.3 Address Pointer
        4. 7.5.1.4 Timeout Function
        5. 7.5.1.5 Device Communication Protocol For I2C
          1. 7.5.1.5.1 Writing A Single Register ( )
          2. 7.5.1.5.2 Writing Multiple Registers ( )
          3. 7.5.1.5.3 Reading a Single Register ( )
          4. 7.5.1.5.4 Reading Multiple Registers ( and )
      2. 7.5.2 Serial Peripheral Interface (SPI)
        1. 7.5.2.1 SPI Shift Register
        2. 7.5.2.2 SPI Communications Command
        3. 7.5.2.3 Standalone Operation
        4. 7.5.2.4 Daisy-Chain Operation
    6. 7.6 Register Maps
      1. 7.6.1  Temperature Data Registers (Read-Only)
        1. 7.6.1.1 LT-Temperature-Data (LT_TEMP) Register (address = 00h) [reset = 0000h, 0°C]
        2. 7.6.1.2 D1-Temperature-Data (D1_TEMP) Register (address = 01h) [reset = 0000h, 0°C]
        3. 7.6.1.3 D2-Temperature-Data (D2_TEMP) Register (address = 02h) [reset = 0000h, 0°C]
      2. 7.6.2  Temperature Configuration (TEMP_CONFIG) Register (address = 0Ah) [reset = 003Ch or 3CFFh]
      3. 7.6.3  Temperature Conversion Rate (TEMP_CONV_RATE) Register (address = 0Bh) [reset = 0007h or 07FFh]
      4. 7.6.4  η-Factor Correction Registers: D1_N_ADJUST and D2_N_ADJUST (address = 21h and 22h) [reset = 0000h or 00FFh]
      5. 7.6.5  ADC-n-Data (ADC_n) Registers (addresses = 23h to 32h) [reset = 0000h]
      6. 7.6.6  DAC-n-Data (DAC_n) Registers (addresses = 33h to 3Eh) [reset = 0000h)
      7. 7.6.7  DAC-n-CLR-Setting (DAC_n_CLR) Registers (addresses = 3Fh to 4Ah) [reset = 0000h]
      8. 7.6.8  GPIO Register (address = 4Bh) [reset = 00FFh]
      9. 7.6.9  AFE Configuration Register 0 (AFE_CONFIG_0) (address = 4Ch) [reset = 2000h]
      10. 7.6.10 AFE Configuration Register 1 (AFE_CONFIG_1) (Address = 4Dh) [reset = 0070h]
      11. 7.6.11 Alarm Control Register (ALR_CTRL) (address = 4Eh) [reset = 0000h]
      12. 7.6.12 STATUS Register (Address = 4Fh) [reset = 0000h]
      13. 7.6.13 ADC Channel Register 0 (ADC_CH0) (address = 50h) [reset = 0000h]
      14. 7.6.14 ADC Channel Register 1 (ADC_CH1) (address = 51h) [reset = 0000h]
      15. 7.6.15 ADC Gain Register (ADC_GAIN) (address = 52h) [reset = FFFFh]
      16. 7.6.16 AUTO_DAC_CLR_SOURCE Register (address = 53h) [reset = 0004h]
      17. 7.6.17 AUTO_DAC_CLR_EN Register (address = 54h) [reset = 0000h]
      18. 7.6.18 SW_DAC_CLR Register (address = 55h) [reset = 0000h]
      19. 7.6.19 HW_DAC_CLR_EN_0 Register (address = 56h) [reset = 0000h]
      20. 7.6.20 HW_DAC_CLR_EN_1 Register (address = 57h) [reset = 0000h]
      21. 7.6.21 DAC Configuration (DAC_CONFIG) Register (address = 58h) [reset = 0000h]
      22. 7.6.22 DAC Gain (DAC_GAIN) Register (address = 59h) [reset = 0000h]
      23. 7.6.23 Analog Input Channel Threshold Registers (addresses = 5Ah To 61h)
        1. 7.6.23.1 Input-n-High-Threshold Register (where n = 0, 1, 2, 3; addresses: 0 = 5Ah, 1 = 5Ch, 2 = 5Eh, 3 = 60h) [reset = 0FFFh]
        2. 7.6.23.2 Input-n-Low-Threshold Register (where n = 0, 1, 2, 3; addresses: 0 = 5Bh, 1 = 5Dh, 2 = 5Fh, 3 = 61h) (reset = 0000h)
      24. 7.6.24 Temperature Threshold Registers
        1. 7.6.24.1 LT_HIGH_THRESHOLD Register (address = 62h) [reset = 07FFh, +255.875°C]
        2. 7.6.24.2 LT_LOW_THRESHOLD Register (address = 63h) [reset = 0800h, –256°C]
        3. 7.6.24.3 D1_HIGH_THRESHOLD Register (address = 64h) [reset = 07FFh, +255.875°C]
        4. 7.6.24.4 D1_LOW_THRESHOLD Register (address = 65h) [reset = 0800h, –256°C]
        5. 7.6.24.5 D2_HIGH_THRESHOLD Register (address = 66h) [reset = 07FFh, +255.875°C]
        6. 7.6.24.6 D2_LOW_THRESHOLD Register (address = 67h) [reset = 0800h, –256°C]
      25. 7.6.25 Hysteresis Registers
        1. 7.6.25.1 Hysteresis Register 0 (HYST_0) (address = 68h) [reset = 0810h, 8 LSB]
        2. 7.6.25.2 Hysteresis Register 1 (HYST_1) (address = 69h) [reset = 0810h, 8 LSB]
        3. 7.6.25.3 Hysteresis Register 2 (HYST_2) (address = 6Ah) [reset = 2108h, 8°C]
      26. 7.6.26 Power-Down Register (PWR_DOWN) (address = 6Bh) [reset = 0000h)
      27. 7.6.27 Device ID Register (DEVICE_ID) (read only address = 6Ch) [reset = 1220h]
      28. 7.6.28 Software Reset (SW_RST) Register (read or write address = 7Ch) [reset = N/A)
        1. 7.6.28.1 SPI Mode
        2. 7.6.28.2 I2C Mode
  9. 8 Application and Implementation
    1. 8.1 Application Information
    2. 8.2 Typical Application
      1. 8.2.1 Design Requirements
      2. 8.2.2 Detailed Design Procedure
        1. 8.2.2.1 Sequencing
        2. 8.2.2.2 Negative GaN Biasing
        3. 8.2.2.3 VDRAIN Monitoring
      3. 8.2.3 Application Curves
    3. 8.3 Power Supply Recommendations
      1. 8.3.1 Power-Supply Sequence
    4. 8.4 Layout
      1. 8.4.1 Layout Guidelines
      2. 8.4.2 Layout Diagram
  10. 9 Device and Documentation Support
    1. 9.1 Documentation Support
    2. 9.2 接收文档更新通知
    3. 9.3 支持资源
    4. 9.4 Trademarks
    5. 9.5 静电放电警告
    6. 9.6 术语表
  11. 10Mechanical, Packaging, and Orderable Information

封装选项

机械数据 (封装 | 引脚)
散热焊盘机械数据 (封装 | 引脚)
订购信息

7.6.9 AFE Configuration Register 0 (AFE_CONFIG_0) (address = 4Ch) [reset = 2000h]

Figure 7-46 AFE Configuration Register 0
1514131211109876543210
ReservedCMODEICONVILDACADC-REF-INTEN-ALARMReservedDAVFGALRReserved
R-0hR/W-1R/W-0R/W-0R/W-0R/W-0R-0R-0R-0R-0h
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 7-23 AFE Configuration Register 0 Field Descriptions
BitFieldTypeResetDescription
13 CMODE R/W 1ADC conversion mode bit. This bit selects between the two operating conversion modes (direct or auto). 0: Direct mode. The analog inputs specified in the ADC channel registers are converted sequentially (see the ADC channel registers) one time. When one set of conversions are complete, the ADC is idle and waits for a new trigger.
1: Auto mode. The analog inputs specified in the AFE channel registers are converted sequentially and repeatedly (see the ADC channel registers). When one set of conversions are complete, the ADC multiplexer returns to the first channel and repeats the process. Repetitive conversions continue until the CMODE bit is cleared (0).
12ICONVR/W0Internal conversion bit.
Set this bit to 1 to start the ADC conversion internally. The bit is automatically cleared (0) after the ADC conversion starts.
11ILDACR/W0Load DAC bit.
Set this bit to 1 to synchronously load the DAC data registers, which are programmed for synchronous update mode (SLDAC-n = 1). The device updates the DAC latch only if the ILDAC bit is set (1), thereby eliminating any unnecessary glitches. Any DAC channels that are not accessed are not reloaded. When the DAC latch is updated, the corresponding output changes to the new level immediately. This bit is cleared (0) after the DAC data register is updated.
10 ADC-REF-INT R/W 0ADC VREF select bit. 0: The internal reference buffer is off and the external reference drives the ADC.
1: The internal buffer is on and the internal reference drives the ADC. Note that a compensation capacitor is required.
9 EN-ALARM R/W 0Enable ALARM pin bit. 0: The ALARM pin is disabled
1: The ALARM pin is enabled
7 DAVF R ADC Data available flag bit. For direct mode only. Always cleared (set to 0) in Auto mode.
0: The ADC conversion is in progress (data are not ready) or the ADC is in auto mode.
1: The ADC conversions are complete and new data are available.
In direct mode, the DAVF bit sets the DAV pin. DAV goes low when DAVF is 1, and goes high when DAVF is 0.
In auto mode, DAVF is always cleared to 0. However, a 1-µs pulse (active low) appears on the DAV pin when the last input specified in the ADC channel registers is converted.
DAVF is cleared to 0 in one of three ways: by reading the ADC data register, by starting a new ADC conversion, or by writing 0 to this bit. Reading the status register does not clear this bit.
6GALRR0Global alarm bit.
This bit is the OR function of all individual alarm bits of the status register. This bit is set (1) when any alarm condition occurs, and remains 1 until the status register is read. This bit is cleared (0) after reading the status register.
开云买球「中国」股份有限公司 | 天博游戏app|中国有限公司 | 英亚体育【中国】有限公司 | 电竞app官网（中国）有限公司 | 千亿体育(中国)有限公司官网 | 欧博游戏官网【中国】有限公司 | IM·电竞（中国）官方网站 | 博鱼体育（中国）有限公司官网 | 易倍体育（中国）有限公司 |